Davidson County · 20 miles from Brentwood
Grading the hillsides of Whites Creek
Whites Creek’s most common soil sits at a median 35 percent slope, which puts slope limits at the center of any grading plan.
TL;DR
Whites Creek is a Metro Nashville community in Davidson County, about 20 miles from Brentwood, with 3,442 people and 1,629 homes in its 37189 ZIP area. Bodine and Dellrose, cherty hillside soils, cover 37 percent of the sample points near the center, the Bodine points at a median 35 percent slope. Pads and yards here are cut into hills, held with walls and benches, and built to Metro’s slope limits: 5:1 for fill, 3:1 for the finished grade.
How steep is the ground in Whites Creek?
Steep, on most of the uplands. Bodine, at 26 percent of the sample points near the center, is a very deep, somewhat excessively drained gravelly soil from cherty limestone on sharply dissected uplands, and its points sit at a median slope of 35 percent. Dellrose, at 11 percent, is very deep cherty colluvium on foot slopes and steep hillsides at a 16 percent median, and Mimosa clay, at 18 percent, runs at 19 percent.
The flat ground is Ocana, also at 11 percent: deep to very deep gravelly alluvium on flood plains, with moderately rapid permeability. Between the hills and the bottoms, a lot in Whites Creek is likely to have a slope to deal with somewhere. Homes are spread thin, 1,629 across the whole 37189 ZIP area, and 39 percent of them were built before 1980.
What slope does Metro allow on a Whites Creek fill?
No steeper than 5:1 for fill and 3:1 for the finished slope, unless calculations justify otherwise, according to the Metro Water Services grading page. A 5:1 fill slope runs 5 feet out for every foot it rises; a 3:1 slope runs 3 feet out. On a hillside that already falls about 1 foot in 3, those numbers decide how much flat ground a pad can actually gain.
Raising the low side of a pad 4 feet with a 5:1 fill slope takes 20 feet of run beyond the pad’s edge. Where that room is not there, a wall carries the change instead. The rest of Metro’s grading test is on our Nashville page.
How do you put a pad or a yard on a Whites Creek hillside?
By cutting into the hill, holding the cut, and building any fill in thin layers. A house or barn pad on a slope like Bodine’s is mostly cut on the uphill side, and the cut face is held by a retaining wall on a compacted base with drainage and stone backfill behind it. A tall change is split into two walls with a level bench between them.
Chert gravel in Bodine and Dellrose digs loose and stony, and the hammer comes out where the excavator meets solid limestone. Fill goes in 1-foot lifts, rolled before the next, so the downhill side of the pad does not creep. Laser-controlled grading keeps the finished pad at its planned elevation.
Can you clear a wooded lot in Whites Creek?
Yes, and on a steep lot clearing is planned around the slope. Land clearing takes out trees, stumps and brush; on a hillside, forestry mulching can open the ground while leaving a mulch layer that slows runoff, where pulling everything would leave bare soil to wash. Debris burns from October 15 to May 15 need a state burn permit, free through BurnSafeTN.org.
On a slope, a gravel drive that has washed at its edges needs its fall rebuilt and its base compacted before new stone goes down, which is driveway prep rather than resurfacing.
Whites Creek is about 20 miles from our Brentwood base, inside the 30 miles we work. Send pictures from the top and the bottom of the slope for a free estimate, and we will agree on the scope and what gets disturbed before work starts. The state’s construction stormwater permit applies once a clearing job reaches one acre.
The work, wherever the job is
Closest to Whites Creek
- Joelton, TN6 mi
- Madison, TN7.6 mi
- Nashville, TN7.8 mi
- Goodlettsville, TN8 mi
- Ridgetop, TN9.3 mi
- Greenbrier, TN10.1 mi
Answers
Whites Creek questions
Can I build a house on a steep lot in Whites Creek?
Often, with more dirt work than a flat lot needs. The pad is cut into the hill, the cut is held with a retaining wall, and any fill is compacted in 1-foot lifts. Metro’s 5:1 fill slope and 3:1 final slope set how much room the grading takes, so the layout starts with those limits.
What is a 3:1 slope on a Whites Creek lot?
A slope that runs 3 feet horizontally for every foot it drops, about 33 percent. Metro wants final slopes no steeper than that unless calculations justify more. Bodine ground near Whites Creek’s center sits at a median 35 percent, so some natural hillsides there are already steeper than the finished grade Metro allows.
Is the soil in Whites Creek rocky?
Gravelly more than rocky, in most places. Bodine and Dellrose, two of the four soils most common near Whites Creek’s center, are full of chert from weathered cherty limestone, and Ocana on the flood plains is gravelly alluvium. Solid limestone can still turn up in a deep cut, and the excavator’s hammer handles it.
Should I mulch or clear my wooded Whites Creek slope?
Mulch it if you only want the ground open; clear it if something is being built. Forestry mulching leaves a layer that helps hold soil on a hillside. A pad, a drive or a wall needs the stumps and the organic layer out, so that ground is cleared and graded instead.