(615) 569-1679 Veteran-owned · Licensed and insured · Since 2021 brentwooddirtworks@gmail.com

Sumner County · 28 miles from Brentwood

Walls and driveways for steep Millersville lots

Every one of the four main soils around Millersville sits at a median slope of 32 percent or more, so almost any level surface there has to be built.

Brentwood Millersville 30 miles 20 10

TL;DR

Millersville is a Sumner County city of 5,836 people, 28 miles from Brentwood. Its ground is steep: Sulphura soil covers 56 percent of the points sampled at a median 38 percent slope, and Dellrose, Hawthorne and Mimosa all sit between 32 and 38 percent. Level yards, pads and drives there are made with retaining walls, benches and compacted fill, and the digging turns up chert and layered rock.

Why are Millersville lots so hard to level?

Because almost none of the land started level. Sulphura covers 56 percent of the points sampled around Millersville, at a median slope of 38 percent, on highly dissected uplands. Hawthorne, another 6 percent, sits at 38 percent too, and Dellrose and Mimosa at 32. A slope of 38 percent climbs 19 feet over a 50-foot depth, and grading that into one flat surface would take a cut or fill nearly 20 feet tall.

The practical answer is terraces. Each one is cut level, its face held by a retaining wall, with the house, the yard and the drive on separate levels. Slopes this steep are where walls and benches stop being optional, because a fill bank at 38 percent will not stay put.

What is in the ground when you dig in Millersville?

Chert, layered rock and very little that is uniform. Sulphura and Hawthorne are both moderately deep and somewhat excessively drained, formed from interbedded siltstone, shale and limestone; in Hawthorne’s case, the limestone is cherty. Dellrose, at 13 percent of the points, is very deep but formed in cherty colluvium, material that worked its way down the hillsides, so it carries chert fragments all the way through.

Chert is a hard, sharp, flint-like stone that wears on equipment and leaves trench walls ragged. Layered siltstone and shale come out in slabs. Neither stops an excavator with a hammer, but both make a dig slower than clay. For an excavation or a trench, the estimate assumes rock, and colluvium on a foot slope gets extra care because loose, cherty material can slide when it is undercut.

How do you get a driveway up a steep Millersville lot?

By making the drive longer than the hill. A straight shot up a 32 to 38 percent slope is too steep to drive safely or to keep gravel on, so the drive is laid across the slope, with a curve or a switchback where the lot allows, and the cut on the uphill side held by a wall when it gets tall.

Driveway prep on that ground means a compacted base thick enough to resist washing, a cross slope so water leaves the surface instead of running down the drive, and a ditch or drain along the uphill edge. Dellrose’s moderately rapid permeability helps on the foot slopes; on the steep Sulphura ground, much of a heavy rain runs off before it can soak in.

What do older Millersville homes run into?

Walls and slopes that have been moving for decades. Thirty-four percent of Millersville’s 2,595 homes were built before 1980, and the median dates to 1993. On hillsides this steep, a wall built without drainage, or fill placed without compaction, has had a long time to lean or creep downhill. Only 11 percent of homes date from 2010 or later.

Millersville is 28 miles from Brentwood in a straight line, inside the 30 the company covers. Goodlettsville and Shackle Island are on this site as well.

Answers

Millersville questions

Do I need a retaining wall to have a flat yard in Millersville?

On most of the steep ground, yes. With the main soils around Millersville at median slopes of 32 to 38 percent, a level area of any size needs a cut held by a wall, or fill held by one. A sloped yard can do without walls, but it will not be flat, and mowing it is its own project.

Why does chert turn up when digging in Millersville?

Because the soils formed from it. Chert is a hard, glassy stone, related to flint, that forms in some limestone. Around Millersville, the Dellrose and Hawthorne soils formed in cherty colluvium and cherty limestone, so fragments run through the soil. It does not stop an excavator, but it wears equipment and makes trench walls rough.

Is a 38 percent slope in Millersville buildable?

Yes, but not by grading alone. Fill will not stand at 38 percent, the median slope on the Sulphura soil that covers 56 percent of the points sampled near Millersville. Building there means benches cut into the hill, retaining walls at each face, and drainage behind them to take the runoff from above.

Can you repair a slipping fill slope behind a Millersville house?

Yes. The loose material is dug out to firm ground, and the slope is rebuilt either at a gentler angle, where there is room, or behind a retaining wall with drainage, where there is not. New fill goes back in 1-foot lifts, rolled, so it does not repeat the problem. Pictures of the slope and any cracks help with the estimate.

Don’t wait until it gets worse

Send us a picture. Get a free estimate.

A phone photo of the yard, the wall or the wet corner tells us most of what we need before anyone drives out.

Call Free Estimate