Davidson County · 12.1 miles from Brentwood
Valley floors and hillsides: dirt work in Bellevue
Bellevue’s ground splits two ways, and the work on each side looks nothing alike.
TL;DR
Bellevue is a Metro Nashville community in Davidson County, about 12 miles from Brentwood; its 37221 ZIP area counts 41,935 people in 21,079 homes. Near the center, deep valley soils like Armour and Arrington sit at slopes of 2 to 4 percent, while gravelly Bodine hillsides run at a median 35 percent. Low ground raises Metro’s floodplain question, and the hills call for walls and benches. Both get answered before the first cut.
What kind of ground is a Bellevue lot built on?
It depends whether you are on the valley floor or up the hill. Armour, at 32 percent of the sample points around Bellevue’s center, is a very deep, well drained soil of stream terraces, foot slopes and valley floors, formed in old alluvium and valley fill, with a median slope of 4 percent. Arrington, at 16 percent, is deep silty alluvium with a thick dark surface on flood plains and along drainageways, nearly flat at a 2 percent median.
Bodine is the other Bellevue. It accounts for 18 percent of the points: a very deep, gravelly soil from cherty limestone on sharply dissected uplands, at a median slope of 35 percent. A hillside lot on Bodine digs loose and stony, and a cut face in it has to be held back.
Does a floodplain change what I can do in Bellevue?
Yes, because staying outside the 100-year floodplain is one of the conditions Metro Water Services sets before a grading job can skip a permit, as its grading permit page spells out. If any part of the work sits inside that floodplain, the exemption is off, however small the job.
Arrington is a floodplain soil by its own description, and it covers 16 percent of the points near Bellevue’s center. That does not place any particular lot in the regulated floodplain, which is drawn on its own maps, but it is a reason to check before planning fill or a new pad on low ground. Our Nashville page carries the rest of Metro’s test.
How do you build on a steep Bellevue hillside?
With walls, benches and fill placed in thin layers. A slope falling at around 35 percent will not hold a level yard or a pad without help, so the ground gets cut into steps, and each step is held by a retaining wall built on a compacted base with drainage and stone backfill behind it. Splitting one tall drop into two shorter walls with a flat bench between them spreads the load.
Where fill goes in to widen a pad, it goes in 1-foot lifts, each rolled before the next, so it does not settle under a slab later. Gravelly fill like Bodine’s compacts well when it is placed thin and poorly when it is dumped deep.
Why does water collect at the foot of a Bellevue slope?
Because the hill sheds it and the flat ground below cannot move it fast enough. Water running off a steep Bodine slope arrives at the valley soils all at once, and a yard on the flat at the bottom gets more than its own rain. A French drain across the foot of the slope catches it before it reaches the house.
Armour, the main valley soil, is very deep, so a drain trench across it seldom meets rock; the trouble there is volume of water, not ledge.
Bellevue is about 12 miles from our Brentwood base. Twenty-four percent of homes in the 37221 ZIP area went up before 1980, and those lots often have older drain lines worth checking before anything new goes in. A picture of where the water runs is the best start to a free estimate.
The work, wherever the job is
Closest to Bellevue
- Pegram, TN5.6 mi
- Belle Meade, TN7 mi
- Forest Hills, TN7.6 mi
- Kingston Springs, TN7.8 mi
- Oak Hill, TN10 mi
- Fairview, TN10.1 mi
Answers
Bellevue questions
Is my Bellevue lot in the floodplain?
That is answered from the flood maps for your address, not from the soil. Near Bellevue’s center, Arrington, a soil of flood plains and drainageways, covers 16 percent of the sample points, so low ground is worth checking. Under Metro’s grading test, work inside the 100-year floodplain needs a permit.
Can you put a level backyard on a steep Bellevue lot?
Often, with walls and benches. On slopes like the 35 percent median of Bellevue’s Bodine ground, the yard is cut into steps and each step is held by a retaining wall on a compacted base with drainage behind it. How much flat ground you gain depends on how much height you are willing to hold.
How do you trench on a rocky Bellevue hillside?
With an excavator, a hammer for any ledge, a skid steer for tight spots and a pipe laser to hold grade. Bodine’s chert gravel on Bellevue’s hillsides digs loose, so a deep trench there is stepped back rather than cut straight down. A Tennessee 811 ticket goes in three working days before.
Do older Bellevue homes need new drain lines?
Some do. Twenty-four percent of the homes in Bellevue’s 37221 ZIP area were built before 1980, and drain lines that old may be cracked, crushed or full of roots. We dig to the trouble spot, show you what failed, and replace the run with new pipe set to grade.