Williamson County · 11.4 miles from Brentwood
Hillside walls and grading in Arrington
Arrington’s rises are steep enough that a level yard or a barn site often means a wall, and the county has a line on how tall one gets before an engineer signs it.
TL;DR
Arrington is unincorporated Williamson County, about 11 miles from Brentwood. Its most common soils, Stiversville and Sandhill, formed over siltstone and sandstone and sit on median slopes of 16 and 25 percent, so walls and benched cuts come up often. A 2015 county engineering form asks for a professional engineer’s certification on retaining walls 4 feet or taller. In the 37014 ZIP area, the median home was built in 1998.
When does a retaining wall in Arrington need an engineer?
At 4 feet tall, going by a Williamson County Engineering form from 2015. The county form asks that retaining walls four feet or more in height carry a professional engineer’s certification, and it sets a setback of 5 feet or the wall’s height, whichever is greater. The form is more than ten years old, so we confirm with the county that it still stands before a wall gets designed around it.
The setback is the part people miss. Under that form, a 6-foot wall needs 6 feet of setback, and on a narrow side yard that room may not exist. Better to learn it before the footing is dug than after. The county’s Land Disturbance Permit thresholds are spelled out on our College Grove page, since the same county rule covers both places.
What kind of ground sits under the hills around Arrington?
Mostly soil weathered from siltstone and fine sandstone, interbedded with shale and limestone. That is how NRCS describes both Stiversville, at 16 percent of the sample points around Arrington, and Sandhill, at 9 percent. Each is deep and well drained. The difference is the pitch: Stiversville’s median slope here is 16 percent, and Sandhill’s is 25.
Braxton fills 13 percent of the points, a very deep clayey soil on gentler ground with a median slope of 9 percent. Gladeville turns up at 5 percent, and it is very shallow over flaggy limestone, so a dig on one of those spots can stop on rock almost at once. Layered stone like that tends to break out in slabs, which is work for a hammer rather than a bucket.
How do you get a flat barn or house site out of an Arrington slope?
By cutting the high side, filling the low side and holding the edges. On a 16 or 25 percent slope, a pad of any size leaves a cut face at one end and a fill bank at the other, and both need a plan. Fill goes in 1-foot lifts, each rolled in before the next, because a thick dump of loose dirt keeps settling under a slab for years.
Where the bank would run too far, a retaining wall holds it instead, built on a compacted base with drainage and stone backfill behind it. Where it can stay a slope, benches break a long face into steps that hold seed. The finished pad is checked with a laser, and so is the fall that carries water away from it.
Are Arrington homes old enough to have drain trouble?
Some are, and a good share are too new for it. For the 37014 ZIP area, the Census count is 3,227 people and 1,391 homes, with a median build year of 1998. Since 2010, 29 percent have gone up, along with 19 percent in the 2000s; 20 percent date from before 1980.
The older houses are where clogged footing drains and roots in old lines turn up, and where a French drain often gets cleaned out or replaced. On the newer ones, the trouble is more often a yard the builder left a little too flat. Gutters that empty right at the foundation are worth a look on either kind, since that water has to go somewhere. We’re about 11 miles away, and a picture is enough to get an estimate started.
The work, wherever the job is
Closest to Arrington
- Triune, TN4.1 mi
- Nolensville, TN6.2 mi
- College Grove, TN7.3 mi
- Smyrna, TN8.8 mi
- Eagleville, TN9.1 mi
- Rockvale, TN9.6 mi
Answers
Arrington questions
Does a short garden wall in Arrington need engineering?
Not under the 2015 Williamson County form, which starts at 4 feet in height. A shorter wall still needs a compacted base, drainage behind it and stone backfill, or it will start to lean. Confirm with the county before relying on the form, since it is an older document.
Is Arrington ground hard to dig?
It depends on the spot. Stiversville and Sandhill, the most common soils, are deep, but they formed over siltstone and sandstone layered with shale and limestone. Where Gladeville shows up, rock is very shallow. We bring a hammer for whatever the bucket won’t take, and say so when it changes the job.
Do you serve Arrington from Brentwood?
Yes. Arrington is about 11 miles from Brentwood in a straight line, well inside the 30 miles we cover. Send a photo of the slope or the problem and a rough idea of its size, and we’ll come back with a free estimate and a clear list of what would be disturbed.
Can a driveway be built up a steep Arrington hill?
Yes, with the grade set before any stone goes down. On slopes of 16 to 25 percent, a driveway usually needs cut and fill along its length, compacted in lifts so the edges don’t slump. Our driveway prep covers the cut, the fill and the compacted base the surface sits on.